Please use this identifier to cite or link to this item: http://tede2.uepg.br/jspui/handle/prefix/1451
metadata.dc.type: Dissertação
Title: Estudo experimental do processo de rotomoldagem: efeitos sobre a morfologia e estabilidade dimensional
Other Titles: Experimental study of rotational moulding process: effect on the morphology and dimensional stability
metadata.dc.creator: Comisso, Tiago Boni
metadata.dc.contributor.advisor1: Carvalho, Benjamim de Melo
metadata.dc.contributor.referee1: Pinheiro, Luis Antonio
metadata.dc.contributor.referee2: Farah, Marcelo
metadata.dc.description.resumo: No presente estudo o empenamento de peças de polietileno linear de baixa densidade (PELBD) moldadas por rotomoldagem foi investigado. O efeito de diferentes fatores como espessura da peça, taxa de resfriamento e diâmetro de tubo de ventilação foi avaliado. Em adição aos experimentos de rotomoldagem, uma técnica alternativa denominada “Hot Press” foi também aplicada para investigar o empenamento de dois diferentes PELBD sob condições típicas da rotomoldagem quanto ao resfriamento assimétrico. Cristalinidade e morfologia esferulítica ao longo da espessura das peças rotomoldadas foram avaliadas por Calorimetria Exploratória Diferencial (DSC) e Microscopia Ótica de Luz Polarizada. Verificou-se que o grau de empenamento aumenta com o aumento da taxa de resfriamento. O aumento do diâmetro do tubo de ventilação é mais efetivo na redução do empenamento principalmente em menores taxas de resfriamento. Nos experimentos de “Hot Press” o PELBD com menor índice de fluidez e maior módulo de flexão apresentou menor empenamento. Nos experimentos de “Hot Press” a espessura das peças afetou o empenamento somente para taxas de resfriamento mais rápidas. Em geral, a cristalinidade e o tamanho de esferulitos se mostraram menores nas posições ao longo da espessura das peças rotomodadas onde as taxas de resfriamento eram mais rápidas.
Abstract: In the present study the warpage of rotationally molded parts of a linear low density polyethylene (LLDPE) was investigated. The effect of different processing factors as part thickness, cooling condition and diameter of the venting tube was evaluated. In addition to the rotational molding experiments, an alternative experimental technique, denominated “Hot Press”, was also applied to investigate the warpage of two different grades of LLDPE under typical rotational molding conditions, which means slow cooling from only one side. Crystallinity and spherulitic morphology along the thickness of the rotationally molded parts were studied by Differential Scanning Calorimetry and Polarized Light Optical Microscopy. It is shown that the warpage increases with the increase of the cooling rate. Increase of diameter of the venting tube is more effective in reducing the warpage of rotationally molded parts mainly for lower cooling rates. In hot press experiments the grade of LLDPE with lower melt flow index and higher flexural strength presented lower warpage. Part thickness affects the warpage in hot press experiments only for faster cooling rates. In general, crystallinity and spherulitic diameter are lower in positions along the rotationally molded part thickness where the cooling rate is faster.
Keywords: rotomoldagem
taxa de resfriamento
microestrutura
cristalização
empenamento
rotational molding
cooling rate
microstructure
crystallization
warpage
metadata.dc.subject.cnpq: CNPQ::ENGENHARIAS::ENGENHARIA DE MATERIAIS E METALURGICA
metadata.dc.language: por
metadata.dc.publisher.country: BR
Publisher: UNIVERSIDADE ESTADUAL DE PONTA GROSSA
metadata.dc.publisher.initials: UEPG
metadata.dc.publisher.department: Desenvolvimento e Caracterização de Materiais
metadata.dc.publisher.program: Programa de Pós-Graduação em Engenharia e Ciências de Materiais
Citation: COMISSO, Tiago Boni. Experimental study of rotational moulding process: effect on the morphology and dimensional stability. 2011. 116 f. Dissertação (Mestrado em Desenvolvimento e Caracterização de Materiais) - UNIVERSIDADE ESTADUAL DE PONTA GROSSA, Ponta Grossa, 2011.
metadata.dc.rights: Acesso Aberto
URI: http://tede2.uepg.br/jspui/handle/prefix/1451
Issue Date: 3-Oct-2011
Appears in Collections:Programa de Pós - Graduação em Engenharia e Ciências de Materiais

Files in This Item:
File SizeFormat 
Tiago Boni Comisso.pdf9.87 MBAdobe PDFView/Open


Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.